2003 Unable to find configuration file x

The specified configuration file could not be found. Check the spelling of the file name on the COPIAFACTS program status screen.

 2004 Unable to open configuration file x

Probably the configuration file does not have the necessary permissions.

 2005 Invalid number of parameters in line #n

Too many or too few parameters were entered on the command line specified. Check the Command Reference section for the details of the correct command syntax.

 2006 $environment ACTIVE must apply to all nodes

 2007 $environment ACTIVE cannot have time parameters

You cannot set the ACTIVE variable to apply at different times of day, or to apply to specific nodes only.

 2010 Invalid do-not-send parameter in line #n

An incorrect keyword has been specified.

 2011 Not enough memory in line #n

Consult your CopiaFacts supplier for assistance.

 2018 Invalid fax modem parameter keyword/value in line #n

An incorrect or duplicate keyword has been specified

 2022 Invalid log file directory in line #n 

 2023 Invalid user profile directory in line #n

 2024 Invalid post office directory in line #n

The specified directory was not found or could not be accessed.

 2025 Unrecognized command in line #n

A mis-spelled or incorrect command was encountered in the configuration file. If the spelling seems correct, check that the command is not one which should appear in a different file type.

 2026 Invalid DTMF wait of x in line #n

The $tone_wait command had a non-numeric seconds value.

 2027 Invalid settle time of x in line #n

The $settle_time command had a non-numeric value.

 2028 Invalid settle flag of x in line #n

The $settle_time command flag parameter was not Y or N.

 2029 Invalid number of rings in line #n

The $no_rings command had a non-numeric count value.

 2030 Invalid baud rate value in line #n

The baud rate specified in the $baud_min was not one of the allowed baud rates. Values between 2400 and 33600 will be rounded to the nearest lower baud rate.

 2031 Invalid same callback line option in line #n

The $callback command same line flag parameter was not Y or N.

 2032 Too many fixed spans in line #n

The configuration limit has been exceeded.

 2033 Invalid request directory in line #n

The specified directory was not found or could not be accessed.

 2038 Cannot reset stats counters

The operation to reset the counters in the statistics file failed.

 2039 Invalid repeat message delay in line #n

The $repeat_msg command had a non-numeric delay value.

 2042 Invalid user jobs directory in line x

The specified directory could not be found.

 2043 Invalid start time x in line #n

 2044 Invalid end time x in line #n

 2045 Start time x not before end time x in line #n

 2046 Invalid day x in schedule in line #n

The time-specifiers on an $environment command have invalid syntax

 2047 Cannot load DLL x (error m) in line #n

The user-DLL specified by $load_dll could not be found or was invalid.  Check also that any DLLs loaded by the user-DLL are available in the same folder or on the PATH.

 2048 Missing voice message x (SVPx.VOX SVPx.WAV or FAXMSG.x) for line x

The indicated required message file could not be found. Check the $vmsg_dir command.

 2050 Not enough memory for log queue

There was not enough memory to store all of the log queue entries. You may have to decrease the log queue.

 2051 Invalid DLL number in line n

The user-DLL specification was incorrect.

 2053 Unable to create TOSEND directory for callback

CopiaFacts was unable to create the sub-directory TOSEND (for pending callback requests) within the request directory. Make sure that COPIAFACTS has write permission for the request directory. You may also create the TOSEND sub-directory yourself using the MKDIR command.

 2054 Unable to create request counter file x

CopiaFacts was unable to create the counter file NEXTFS in the TOSEND directory. This counter file is used to assign control numbers to outbound requests. Make sure that COPIAFACTS has write permission for the TOSEND directory.

 2055 Unable to create SENT directory for callback

CopiaFacts was unable to create the sub-directory SENT (for successfully completed outbound requests) within the request directory. Make sure that COPIAFACTS has write permission for the request directory. You may also create the SENT sub-directory yourself using the MKDIR command.

 2056 Cannot initialize DLL for SMS

The DLL for the specified SMS provider interface cannot be loaded or initialized

 2057 Unable to create fax mail counter file x

CopiaFacts was unable to create the counter file NEXTMCF in the post office directory. This counter file is used to assign control numbers to messages received. Make sure that COPIAFACTS has write permission for the post office directory.

 2058 Invalid line number override in line #n

An incorrect line number was found in a secondary $user_profiles command specifying an override directory for a specific line.

 2059 Invalid ASCII parameters in line #n

An invalid font was specified on the $ascii_font command.

 2060 Unable to load default user profile x

An error was encountered and reported in loading the default user profile specified in the $default_profile command. This error prevents the program from starting. Errors in subsequent processing of a user profile will only cause the affected call to fail.

 2061 Unable to load default mail user profile x

An error was encountered and reported in loading the default mail profile specified in the $mail_profile command. This error prevents the program from starting. Errors in subsequent processing of a user profile will only cause the affected call to fail.

 2062 Invalid extra request directory count in line #n

The numeric parameter on the $request_dir command is outside the range 1 to 9.

 2063 Invalid phone mask access code s in line #n

The phone mask code was not one of c + - ~ or their keyword equivalents.

 2064 Missing phone mask parameter in line #n

Configuration file phone masks with code + or c must have an output mask specified.

 2065 Invalid PRI board number in line #n

The board number was not recognized as an installed board.

 2066 Too many excluded device names in line #%d

The limit on the number of $exclude_channel commands was exceeded.

 2067 Phone mask '-' or '~' should not have output mask in line #n

Only configuration file phone masks with code + or c should have an output mask specified.

 2076 Warning: WFP keyword ignored on $convert_types

Winfax Pro files are no longer converted explicitly in the Document Converter.

 2078 Partial-retry max time must be >=0, less than 2 days, in line #n

 2079 Partial-retry minimum completion invalid in line #n

The $retry_partial command was invalid

 2080 First parameter must be DATA5 to DATA9 in line #n

 2081 Invalid field width n in line #n

 2082 Log field lines out of sequence in line #n

The $log_field command was incorrectly specified, or you have left a gap in the definition of field numbers.

 2084 Invalid display box number n in line #n

The display box number must be between 3 and 8 inclusive.

 2085 Invalid retry delays class letter in line #n

The letter must be A..H.

 2086 Invalid characters in delay string in line #n

The letter specified is not one of the allowed prefix or suffix characters.

 2088 Invalid directory as SET ACTIVE=s

 2089 Invalid directory as SET COVERTMP=s

The directory specified on an environment variable does not exist or does not have the necessary permissions.

 2090 Invalid voice parameter name in line #n

The parameter name on a $bfv_parm, $cpb_parm or $dcb_parm command was not recognized.

 2091 Invalid speed parameter (must be -5 .. 5) in line #n

 2092 Invalid volume parameter in line #n

The parameter on a $speed or $volumecommand was invalid.

 2093 Only two hangup tone specifications are allowed in line #n

There were more than two $hangup_tone commands which define tones for the specified line. A command with * as the line parameter is counted for all lines.

 2094 Cannot pre-load IBC file s, code d in line #n

 2095 Cannot re-load IBC file s, code d in line #n

The specified infobox collection (IBC) file could not be loaded, either because the file was not found or because it was invalid or corrupted.

 2096 Invalid or duplicate map drive letter in line #n

The $map_drive command had invalid or duplicated drive letters.

 2097 Invalid retry page count in line #n

The parameters for Dialogic VFX/40 page retries in $retry_page were invalid.

 2098 Cannot initialize e-mail security option x in line #n

The e-mail security option is not supported.

 2099 Invalid telephony parameter name in line #n

The keyword used to set low-level parameters was invalid or spelled incorrectly.

 2100 Duplicate global tone ID in line #n

The same tone was defined multiple times in $global_tone.

 2101 Invalid e-mail security option x in line #n

The e-mail security option keyword has not been recognized.

 2102 Invalid tone-id code in line #n

The number used to define a hangup or special tone is invalid.

 2103 Priority level must be in range 1 to x in line #n

The priority level on the $line_priority command is invalid.

 2104 Voice channel must be assigned before $cpb_parm in line #n

Check the allocation of voice channels in CFHWL, and that a $cpb_parm command is not included for a line with no voice capability.

 2105 Unable to load parameter file in line #n

The file containing override retry parameters and specified in $retry_parms could not be found or read.

 2108 Invalid voice parameter value in line #n

The voice parameter was not one of the valid keywords.

 2109 Error on line n of retry parameter file x

The file containing override retry parameters could not be read.

 2110 Only three dialtone specs are allowed in line #n

Too many dial tone specifications have been given.

 2111 Invalid line group range spec (error x) in line #n

Invalid syntax in the line group specification.

 2112 Too many line groups in line #n

The limit on the number of line groups (40) has been exceeded

 2113 Warning: CFG command in line #n affects no lines in this node

The line group specification causes the command not to affect this machine.

 2114 Invalid log option x in line #n

The keyword was incorrect or not spelled correctly

 2115 Too many kill groups (more than x) in line #n

 2116 Invalid kill group count x in line #n

 2117 Invalid kill group outcome x in line #n

The $kill_group specifications were invalid

 2118 Invalid macro character >x< in line #n

Valid macro characters are ` ~ # % ^ | &

 2119 Invalid email parameter in line #n

An incorrect keyword was specified in $email_options.

 2120 CF8MSMQ not loaded for line #n

An operation was attempted which requires MSMQ support, but CF8MSMQ.DLL has not been loaded.

 2121 Warning: Voice format keyword x ignored for x board in line #N

A specified voice format keyword was not supported on the voice board for the line.

 2122 Invalid parameter count for Dialogic Diva board in line #d

An incorrect number of parameters have been supplied for Diva global tone detection

 2123 Duplicate command in line #d

A duplicate command has been encountered for a command which must only appear once.